FYI. Remington model 32 and K model 32.

Discussion in 'Skeeters Corner' started by Bulge, Jan 9, 2015.

  1. Bulge

    Bulge Active Member

    Just in case some of you are not aware, a lot of Krieghoff parts will fit right onto a Remington model 32. I have a Rem 32 26.5" skeet gun that I was trying to sell and was asked if the barrel was loose at all. I had to be honest and tell the guy that the barrel had a minimal amount of play. I started to think about that and went into my Krieghoff parts box and had another set of hinge pins. Once I changed them the whole gun seemed to tighten up. I have swapped other worn Remington parts w, Krieghoff parts and they do interchange. Bulge.

    BTW, the skeet gun is for sale.
     
    Last edited: Jan 14, 2015
  2. Ken Cerney

    Ken Cerney HOF Muscoda Gun Club Past Wisconsin Director Founding Member HOF Muscoda Gun Club

    Bulge, How about the 3200. Any of the parts interchange?
     
  3. Bulge

    Bulge Active Member

    No. Different gun as far as I know. Only thing similar is the look of the barrels. Bulge.
     
    Last edited: Jan 10, 2015
  4. Dbl Auto

    Dbl Auto Active Member Founding Member

    Here is a great vintage Remington M 32 pic. My Uncle holding my Grandfather's M 32 TC.
    Doug Allison
    [​IMG]
     
  5. Bulge

    Bulge Active Member

    What's the serial# I may have that gun now. LOL.
     
  6. Dbl Auto

    Dbl Auto Active Member Founding Member

    I wish I knew what the number was on that TC. My Grandfather sold it after a slump in the 50's, you know how it goes. It was last seen in a small shop in Upper Sandusky, Ohio in the early 60's. Dad recalls his Father telling the serial number to the guy behind the counter and it matched.

    The pic is from the early 1940's.
    Doug Allison
     
  7. Ken Cerney

    Ken Cerney HOF Muscoda Gun Club Past Wisconsin Director Founding Member HOF Muscoda Gun Club

    Thanks Bulge. I knew that Remington sold the 32 to the K guys but didn't know if all of the 3200 changed from the original.
     
  8. Gerald

    Gerald Mega Poster Founding Member

    Barrels come very close to fitting as well. The K80 mono-block miked the same as my ou barrels.

    When the K80's came out years ago I tried one on my 32S frame and it almost fit perfect.

    I would have needed to change the hinge pins to the larger ones, but it locked up perfect and the top latch in the proper position.

    Firing pins on the K32 fit as well.

    Great design of a shotgun.


    Regards....Gerald
     
  9. Joe Winnicki

    Joe Winnicki Guest

    Great picture ! Looks like those barrels are 40 inchers ! In today's world your grandfather would be getting a visit from child protection services.

    Joescout
     
  10. Old1Eye

    Old1Eye Old 1 Eye

    Just a note the first K 32 guns up to sea # 500 or so were exact copies of the Rem 32 the rib was also identical. Then Krieghof started to upgrade the gun and it had ongoing changes right up to the K 80 introduction. I am sure some parts interchange like the K 80 trigger fits the later K 32 just have to find an old-timer that knows what's what.
     
    Jack Olson likes this.
  11. amboy49

    amboy49 Well-Known Member

    My Kreighoff Model 32 has a K80 trigger ( not sure if the "guts" are K80). The stock cutout for the trigger guard is different on the K80 and the Model 32.

    FE14E102-651F-4889-9BF8-D426ACC11ABC.jpeg
     
  12. Ernroe

    Ernroe Well-Known Member

    Beautiful gun!! I had a Model 32 4 brl set with Dockwiler Wood, it had been upgraded with crown grade engraving. This is one that got away that I wish I had back.