Up
Also, there is a small 1/4” dent in the front of the grip. See photo below. [ATTACH]
I am not sure. I purchased this wiring previous owner. I can find his contact.
Additional info: - this is not a wood grip offered by PFS recently. It is custom-made by a Curtis Dutton before PFS offering wood grips - there is no...
Nice wood grip and matched Ultra Fit Comb for 725. The grip would fit small to medium hand better. $250 shipped to CONUSA [ATTACH] [ATTACH]
I will take it.
FYI, I know Joe for years and I recommend him this site.
Is the case included?
Is there any cast on the stock? Thanks.
agree. The description is the same too.
Sorry, I want to withdraw the offer to “ take it”. I am leaving the country for a 2-week trip.
Sorry, it was sold long ago
See my previous posting on Ljutic triggers. Basically, check your release block width one is 0.6" wide and another is about 0.534" wide....
Sold
Yes.
Top
Withdraw. NO longer for sell.
The SN of my Lujitc was probably 2513 or 2616 (not sure about the last two digit). The "Wright" chock information paper has a date of 4/14/2005 at...
Six Chokes for Ljutic Mono. Sell as a set. $150 shipped to CONUSA See measurement shown. Wright Chokes: #9 (XFULL), #8 (FULL), #6 (IM) # 4(LM). See...
GRACO Barrel weights. Never been used. $50 shipped to CONUSA. Barrel Weight Kit w/Adapters Easy to install, kit includes a barrel clamp and three...
Yes
Reduce to $750
Reduce to $800
Like new. Used only a couple of times. Included everything in the original packaging plus a shoulder carrying bag (repurposed camera bag) with a...
Great condition. One DVDV Ask $40 shipped to CONUSA [ATTACH] [ATTACH]
See photo. Great condition not scratch Ask $40 shipped to CONUSA. [ATTACH] [ATTACH]
Original cost $109. Ask $80 shipped to CONUSA No scratch or damages. [ATTACH] [ATTACH]
I will take the three used TS A391 for $10 each plus shipping.
I have seen post that High Plain stocks are not true MC parallel comb. Please make sure you check it out.
Looking for Gen 1 Perazzi #6 and/or #4 chokes for 18.5 bore. (For a TMS) Based on my search online, these are 45mm long (about 1 3/4 inches) like...
sorry, the case was sold earlier.
FYI, there are two different sizes of inertia block width in Ljutic triggers. It may be helpful buyer. See photo below. [ATTACH]
Corrections to the original post (from Mike of Ljutic) 1) Constriction is 0.035 2) Pattern to 70/30
There was a question about rings at the end of the barrel. Here is the photo [ATTACH]
Thanks Mod! New price of $2400 shipped WITHOUT the Negrini case. I will include a leather soft case.
I have a complete 1100 Trap receiver available. Please PM. [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH]...
Like New Negrini glasses case. Ask $45 shipped to CONUSA. [ATTACH] [ATTACH] [ATTACH]
This is a Citori grip modified for Citori 525. Taken off from a 525 I sold a while back. Ask $75 shipped to CONUSA. [ATTACH] [ATTACH] [ATTACH]
What about mark this as “Sold”, then post a new ad of the correct gun?
There seems two types of mono trigger for different widths of action release blocks. Some will fit PRO too. You need to measure the with of release...
In very good condition. Some rubbing marks inside the compartment. See photo. Dimension photo taken from Negrini web site. New price is $419. ask...
Sold locally.
UP
Additional pictures: [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH]
Separate names with a comma.
