FOR SALE - Perazzi MX8 32" O/U barrels LOWERED

Discussion in 'For Sale-Wanted to Buy' started by bob lowman, Sep 6, 2019.

  1. bob lowman

    bob lowman Mega Poster

    I have a set of MX8 32" O/U barrels that have been Pro Ported and Wilkinson did the fixed chokes but it is not stamped. The bore is 733 and the chokes are 25th top and 12th bottom. Bluing is very good. Ser # 67704

    (( $2200 Delivered to your address in the Lower 48 ))

    Any questions please send a conv message for info and contact # -- Thanks Bob
     

    Attached Files:

  2. Don Karlen

    Don Karlen Mega Poster

    Are you sure this is an mx8 o/u barrel?
     
  3. tvbh40a

    tvbh40a Well-Known Member

    It says Perazzi on the side of the barrel. Kind of hard to read but it is there. How tall is the rib in mm?
     
  4. bob lowman

    bob lowman Mega Poster

    It says -- Imported - Perazzi USA - Rome - New York and the rib looks to be about 11 mm high and width looks to be 11mm x 8mm
     
  5. ljutic329

    ljutic329 Mega Poster Founding Member

    That's MX-3, Mx-3 Special or Ga-88 barrels
     
  6. bob lowman

    bob lowman Mega Poster

    Thanks for the info and they have to be an MX3 Special or GA-88 because they are type 4 barrel lug
     
  7. Don Karlen

    Don Karlen Mega Poster

    What is is a perazzi Ga 88???
     
  8. tvbh40a

    tvbh40a Well-Known Member

    Grand American 88
     
  9. Don Karlen

    Don Karlen Mega Poster

    Thanks!
     
  10. mpolans

    mpolans Mega Poster

    Looks like MX-3 Special barrels. Regular MX-3 would have a round monobloc. The only bummer (for me) is the porting. Even then, if the bluing is good and it isn't all dinged up, at $2200 shipped, that's a steal. If I didn't already have a couple sets of those, I'd be all over them.
     
    wpt likes this.
  11. bob lowman

    bob lowman Mega Poster

    Thanks Mark and the precious owner told me they were on his MX3 Special and he bought a set of 30" barrels to shoot doubles with
     
  12. vdt

    vdt Mega Poster Founding Member

    just might be off a DB-81
     
  13. JJM

    JJM Well-Known Member

    MX3 Special Barrels work very nice on a MX 15 to make a combo.
     
  14. richie h

    richie h Active Member

    Is this something you had done . What is the reasoning behind this. Thanks
     
  15. bob lowman

    bob lowman Mega Poster

    Richie h you have a conv message
     
  16. DDM

    DDM Mega Poster

    I have done the same, put mx3 special o/u on mx15. The mx3 rib is just a little lower than the flattest setting of the mx15 rib.
     
  17. JJM

    JJM Well-Known Member

    richie h
    To make the MX15 a combo
     
  18. bob lowman

    bob lowman Mega Poster

    LOWERED to $2150
     
  19. bob lowman

    bob lowman Mega Poster

    UP
     
  20. GTF

    GTF Member

    i'm looking for a type4, 32", w "4mm" rib - my understanding is 4mm is not the height from barrel to top of the rib but some other perazziesque measurement. if so do you know if this barrel came from the original receiver or prev fitted to another. thx!